LonghandMath calculators

Percentage Change Calculator

Find the percent increase or decrease between an old value and a new value, apply a percent change to a number, or work backward to the original value. Each tool shows the formula and every step.

Percent change from an old value to a new value

Apply a percent change to a number (use a negative percent for a decrease)

Find the original value before a percent change

What is percentage change?

Percentage change describes how much a value rose or fell compared with where it started, expressed as a percent. A positive result is a percent increase, and a negative result is a percent decrease. It is used for prices, salaries, populations, grades and any figure that changes over time.

The percentage change formula

To findFormula
Percent change(new − old) ÷ |old| × 100
New value after a changevalue × (1 + percent ÷ 100)
Original value before a changenew value ÷ (1 + percent ÷ 100)

How to calculate percentage change step by step

  1. Subtract the old value from the new value.
  2. Divide the difference by the old value.
  3. Multiply by 100 and add a percent sign.
  4. Read the sign: positive is an increase, negative is a decrease.

Worked examples

A price rise: 800 to 880

The change is 80, and 80 ÷ 800 = 0.10, which is a 10% increase.

A price drop: 100 to 75

The change is −25, and −25 ÷ 100 = −0.25, which is a 25% decrease.

Applying a change: 80 increased by 12%

80 × 1.12 = 89.6. For a decrease, 60 reduced by 25% is 60 × 0.75 = 45.

Reversing a change

A value is 55 after a 10% increase. The original was 55 ÷ 1.10 = 50. Do not subtract 10% from 55, because the 10% was taken from the original value, not the new one.

Why +20% then −20% does not return to the start

Start at 100. A 20% increase gives 120, and a 20% decrease of 120 gives 96. The second percentage applies to a larger number, so you end 4% below where you began.

Percentage change vs percentage points

A percentage point is the arithmetic gap between two percentages. If an interest rate moves from 4% to 6%, it rises by 2 percentage points, but the percentage change is (6 − 4) ÷ 4 = 50%. News reports often mix the two, so check which one is meant.

Zero and negative starting values

Percent change from zero is undefined, because you would divide by zero. For a negative starting value, the formula uses the absolute value of the old number so that the sign shows direction. Going from −4 to −8 is a drop of 4 units, which the formula reports as a 100% decrease. For percent differences with no starting value, or for measurement error, see the percent error calculator.

Common percentage change mistakes

The most common mistake is dividing by the new value instead of the old one. Another is adding successive percentages: two changes of +10% and +10% give +21%, not +20%. Reversing a percentage by subtracting the same percent is also wrong. For other percent problems, such as finding a percent of a number, use the full percentage calculator.

Frequently asked questions

How do you calculate percentage change?

Subtract the old value from the new value, divide by the old value, then multiply by 100. Rent rising from 800 to 880 is 80 ÷ 800 = 0.10, a 10% increase. A negative answer means the value fell.

Is a negative percentage change a decrease?

Yes. A negative result means the new value is lower than the old one. A change from 100 to 75 is −25%, a 25% decrease. The magnitude gives the size of the change and the sign shows the direction.

How do you reverse a percentage change?

Divide the new value by (1 + percent ÷ 100). If a price is 55 after a 10% increase, the original was 55 ÷ 1.10 = 50. For a decrease, use a negative percent: 75 after a 25% drop means 75 ÷ 0.75 = 100.

Why can't you calculate percentage change from zero?

The formula divides by the old value, and dividing by zero is undefined. Going from 0 to 5 is an increase of 5 units, but it has no meaningful percentage. In that case, report the absolute change instead.

What is the difference between percentage change and percentage points?

Percentage points measure the difference between two percentages directly, while percentage change compares them relative to the starting percentage. A move from 4% to 6% is 2 percentage points, but a 50% increase in the rate.

Why doesn't +20% followed by −20% bring you back?

Each percentage applies to a different base. A 20% rise takes 100 to 120, and a 20% fall from 120 is 24, leaving 96. To undo a 20% increase you need a decrease of 20 ÷ 120, about 16.7%.

More Arithmetic and Fractions calculators

Browse every arithmetic and fractions calculator.

Other calculators

Related topics on this page: percent increase, percent decrease, percentage difference, reverse percentage, original value, successive percentage changes, percentage points