What is percent error?
Percent error measures how far a measured value is from the accepted value, as a percent of the accepted value. It is widely used in science labs to judge the accuracy of a measurement. A small percent error means the measurement is close to the true value.
The percent error formula
| Quantity | Formula |
|---|---|
| Error | measured − accepted |
| Absolute error | |measured − accepted| |
| Relative error | |measured − accepted| ÷ |accepted| |
| Percent error | |measured − accepted| ÷ |accepted| × 100 |
How to calculate percent error step by step
- Subtract the accepted value from the measured value.
- Take the absolute value of the result.
- Divide by the absolute value of the accepted value.
- Multiply by 100 and add a percent sign.
Worked examples
Gravity in a physics lab
A student measures g as 9.6 m/s², and the accepted value is 9.8 m/s². The absolute error is 0.2, so the percent error is 0.2 ÷ 9.8 × 100 ≈ 2.04%.
Density of a mineral
A measured density is 2.65 g/cm³ against an accepted 2.70 g/cm³. The error is 0.05, and 0.05 ÷ 2.70 × 100 ≈ 1.85%.
Boiling point of water
A thermometer reads 98°C where 100°C is expected. The absolute error is 2, so the percent error is 2%.
Percent error, percent change and percent difference
| Measure | Compares | Divide by |
|---|---|---|
| Percent error | A measurement with an accepted value | The accepted value |
| Percent change | An old value with a new value | The old value |
| Percent difference | Two values with no reference | Their average |
See the percentage change calculator for the second, and the percentage calculator for percent difference.
What counts as a good percent error?
It depends on the instrument and the experiment. A school lab using a ruler may accept several percent, while a precision measurement may need a fraction of a percent. Your teacher or the experiment instructions usually give the target. A negative signed error means the measurement was below the accepted value, and a positive one means it was above, which can reveal a systematic bias.
Common percent error mistakes
The classic mistake is dividing by the measured value instead of the accepted value. Another is leaving out the absolute value, which can give a negative percent. If the accepted value is zero, percent error is undefined. Always keep both values in the same units, and report a sensible number of significant figures.
Frequently asked questions
What is the formula for percent error?
Percent error equals the absolute value of (measured − accepted), divided by the absolute value of the accepted value, times 100. It expresses the size of the error as a percent of the true value, regardless of whether the measurement was too high or too low.
Can percent error be negative?
By the standard definition it cannot, because it uses an absolute value and reports only the size of the error. Some courses keep the sign to show direction: a negative signed error means the measurement was below the accepted value. Check your course's convention.
What is the difference between percent error and percent difference?
Percent error compares a measurement with a known accepted value and divides by that value. Percent difference compares two values that have no reference, such as two trials, and divides by their average. Use percent error whenever you know the true value.
What is a good percent error?
There is no single threshold, because it depends on the instrument and the experiment. A few percent may be fine in a classroom lab, while precise work demands much less. Check your instructions, and consider whether your equipment could plausibly produce that much error.
Why divide by the accepted value?
The accepted value is the reference you are judging against, so the error is measured relative to it. Dividing by the measured value would give a different number that depends on the mistake itself, which is not the standard definition.
What if the accepted value is zero?
Percent error is undefined, because you cannot divide by zero. In that case, report the absolute error instead, which is the size of the difference in the original units.
More Arithmetic and Fractions calculators
- Percentage Calculator
- Fraction Calculator
- GCF and LCM Calculator
- Exponent and Root Calculator
- Order of Operations Calculator
- Percentage Change Calculator
Browse every arithmetic and fractions calculator.
Other calculators
- Quadratic Formula Calculator
- Mean, Median, Mode Calculator
- Pythagorean Theorem Calculator
- Standard Deviation Calculator
- Slope, Distance and Midpoint Calculator
- Linear Equation Calculator
- Area Calculator
- Volume Calculator
- Circle Calculator
- System of Equations Calculator
- Scientific Calculator with Steps
- Z-Score Calculator
- Permutation and Combination Calculator
- Midpoint Calculator
- Distance Formula Calculator
- Equation of a Line Calculator
- Variance Calculator
Related topics on this page: absolute error, relative error, experimental value, accepted value, measurement error, percent difference, lab report